car wont go into gear after clutch install

Voting is now live for Aprils E46 of the Month Challenge. The one way of checking it is to start the car after engaging the gear and clutch.

The Reasons For Manual Transmission Won T Go Into Gear When Running

After clutch replacement hard to shift into gear Transmission ATMT Driveline Welcome to the North American Subaru Impreza Owners Club.

. Wont go into gear after clutch install Bennmercado. Tighten to around 9lbs of torque at first for the linkage. Pulling everything apart was pretty easy.

After about 20 minutes of starting in second gear and driving in second I could shift freely. Remove the clutch disc and inspect the spline at the center. The car starts moving if you push it to 1st.

Car wont go into gear while the engine is running after new clutch install. I get in car turn motor on depress clutch but cant shift into any gear. 2 of 2 Go to page.

Checked CMC and slave for leaks and didnt find. After some 20 miles on the road the car stopped getting into gears again and then ended up stuck in 3rd. Thank you Rod Knox But on a separate issue Ive got grindingscraping in first second and third which got better with the new clutch and bearing install but still quite bad in first and second So before this new clutch install the car was making this grindingscraping noise.

If the vehicle was shafting fine prior to installation or was able to be driven whether the clutch was slipping or not and now the vehicle will not move at all the issue is with the workmanship or the clutch set itself. Tester September 2 2016 904pm 7. Look into the clutch.

When the car was raised front end up still and put together enough. It did not go into any gear while running with the clutch all the way to the floor. 1 Used the clutch alignment tool to install the clutch disc between the pressure plate and flywheel 2 Torqued the pressure plate onto the flywheel to spec 3 Resurfaced the flywheel if it is too worn 4 Have clutch fluid and bled the clutch afterwards 5 Make sure the throw out bearing is attached to the clutch fork correctly.

If its low or out then the slave or master is leaking and you will need to replace both. 04-29-2014 0839 PM 8. When I shut it off it went into every gear without an issue.

I just had my local shop install a new LUK clutch kit on my 2002 325i everything worked great for the first day until the next morning I could no longer put the car into gear unless the engine was off. So it seemed that the clutch was not disengaging fully. Wont go into gear.

I did not measure it at all but tried to go by the casting marks which look like where the area should have been. 121613 UPDATE SOLUTION - THE CLUTCH PEDAL NEEDED TO BE ADJUSTED. Adjusted the pedal even put a new slave cylinder on in case it was that.

There is either still air in the clutch system you have a bad master or slave cylinder the clutch isnt right or the TOB isnt right. Throwout is on the shaft and pilot is in the flywheel. Well the clutch isnt releasing fully which is why it wont go into gear with the engine running.

If the clutch arm IS working and the pedal feels normal sometimes you can put in gear and start it with the clutch pedal depressed and drive it and goose the gas to break the. This then caused the clutch disc to sit at an angle when it was installed. Hey guys i Have a 2006 V6 so ive got a headache.

Mechanic test drove the car. How to fix a car that wont go into gear DIY with Scotty Kilmer. 2005 BMW 330Ci Japan Red Tan interior.

Parks and turns off car for me to test it out. The pedal felt firm. If the engine cools for over 2 hours I can no longer shift this happens every.

If the vehicle stumbles forward you should take it to a servicing shop. The problem could be the result of a stubborn clutch refusing to disengage. This happened to me once.

Yeaa it could be really possiblebut clutch fluid is not the reason why you cant put into first gearanyway if there is no oil in your tranny you would be able to shift into first gearit would be hard but youll be still able to do it talkning bout leak under your car first check if your hydraulic system is oki had that problem before toowhen i went to change my clutch the. The car will shift fine once you are moving it will go into 1st-5th gears just fine if the car comes to a dead stop it will not go into any gear and if you try to put it in reverse while the car is running it will just. They said the clutch is good it has to be in the hydraulics.

The clutch was slipping at high RPMs but functioning. I installed a ACT xtreme duty clutch on my 02 wrx and ever since Ive had it installed it wont go into gear while the engine is running and the car is not moving. Either way modular clutch or not the transmission has to be removed.

I got a clutch disc where the spline was not machined straight thru but instead was machined at an angle. Dougdye325 Premium Member. Then it gets bad again.

The clutch isnt disengaging it seems. How to bleed the clutch system. Took the old modular clutch apart Drilled out the rivets.

Ill do that before I install the engine back into the car. Up to 8 cash back on September 09 2016. If I put it in first gear and then started it with the clutch all the way in it would move forward slowly.

21 - 26 of 26 Posts. Youre supposed to change both when you do a clutch. How to replace clutch master cylinder.

Put it all back together and the shifter goes through all the gears no trouble but when turned on will not go into any gear. It will sometime go into 4th but grind or clunk pretty badly and the car will lurch forward. If the pilot bearing got put in a little crooked and I mean just a hair off itll keep that shaft turning independantly of the engine and cause the car to go into gear.

Jump to Latest Follow Hey everyone. Took my clutch fork out and ground the wear marks flat then built it back up by welding it. Up to 25 cash back Transmission stuck in gear after clutch install.

If the usual pedal. He said it would take a day but ended up taking 3 days apparently the job was bigger than he thought. If you can put it in gear with the engine off but not when its running check the clutch master fluid.

Sometimes its impossible to go into 1st or reverse. The last time I had a mustang shop bleed it and it was OK for a week alittle notchy but going in gear. Just finished a clutch replacement about my 20th one however when starting the car and depressing the clutch it will not go in gear.

An experienced mechanic should diagnose the clutch system because it indicates that the hydraulic clutch not putting. Bleeding can be tricky. Our car wouldnt get into gears with engine on engine off was fine mechanic said we needed a new clutch.

The clutch kit was brand new flywheel was resurfaces pivot ball and. He may or may not have a defective unit. All gears engaged perfectly fine.

How Clutches Work Howstuffworks